It’s no secret that the modern bicycle is a versatile machine, offering options for transportation, recreation, fitness, competition and employment. Cycling provides a host of health benefits, including improved cardiovascular functioning, leg strength, balance and coordination, plus improvements in mood and weight management.
For those living in seasonal climates, our bicycles typically lie dormant during the cold winter months and resurface in spring. But before you head outside for your first ride of the season, spend some time getting your bike ready. These basic bike maintenance tips will help ensure a safe, efficient ride all season.
Before you think about taking your bike for a spin, make sure you give it a thorough tune-up. Don’t worry; most of these checks are easy to administer.
If you don’t want to get your hands dirty though… the Drouin Cycles team is happy to help.
Contact Us today to book your bike in for a tune-up.
Tune-up task #1: Clean your bike
What to do: Use a basic biodegradable cleaner such as Simple Green, a towel and an old toothbrush to clean everything: the frame, chain, chain rings, cassette, derailleurs, pedals, brakes, and seat. Make an effort to use as little water as possible. Also, remove the seat post (the tube connected to your seat that slides into the frame) and after cleaning it, add a small amount of bicycle grease before reattaching it. This grease will last longer than oil, which dries out faster, and will also act as a barrier against rust in the seat tube.
Tune-up task #2: Inspect your brake system
What to do: First, check the brake pads, the rectangular rubberised component that actually rubs against the metal tire rim. Just like the brakes in your car, bicycle brakes wear down over time and need to be replaced. Use a flashlight to assess if the pads are wearing evenly. If you notice a ridge or other uneven wear pattern, you may need to have your brakes adjusted. Replace the pads if they show excessive wear. Next, squeeze the brake lever on your handlebars and watch the brake pads. They should hit the rim at the same time. If they don’t, you can adjust your brakes with the brake arm tension screw, which is located on one of the brake lever arms near the tyre. If you notice too much slack in the cable when pulling your brakes, roll out the barrel adjuster at the end of the lever (where the cable enters the housing) to add tension to the brake cable, thereby making the brakes react more quickly.
A poor braking system could lead to loss of control while riding, which could lead to accidents and serious injury. If you conclude that your brakes are not working properly, then do not ride your bike; take it to a bike shop to be repaired. If your brakes fail while riding, figure out a way to stop your bike (perhaps go up hill or steer onto the grass or other high friction surface). After you have come to a complete stop, get off your bike and walk home or call for a lift. Have the brakes repaired before riding again.
Tune-up task #3: Watch your wheels
What to do: Clean the wheels with rubbing alcohol and a clean, dry cloth. Inspect the rims for nicks, scrapes, dents or other damage. Next, elevate one end of the bike and spin the wheel. The wheel should move smoothly, without wobbling. Repeat for the other wheel.
Damaged rims cause uneven wear to tyres and brake pads, which can shorten their lifespan. In addition, uneven tyre wear usually leads to flat tyres or a blown tyre while riding—a potentially dangerous situation. Replace your wheels if denting or other damage is excessive. A wobbly rim can be adjusted with a spoke wrench—a simple fix that a bike repair shop can handle better than most do-it-yourselfers. Adjusting spokes yourself can lead to more problems if you do not know what you’re doing.
Tune-up task #4: Inspect the drivetrain
What to do: You will need a partner or bike stand to assist with this part of the tune-up. Raise the rear wheel and spin as you did when checking the wheels (task #3 above). This time, shift through all the gears. Shifting should be smooth and easy to perform. Inspect the chain, chainrings, derailleur and cassette for damage (excessive wear, missing teeth, dents, scrapes, etc.). Note that small chainrings wear out sooner than large chainrings and that chains are the most frequently replaced component of the drivetrain.
If shifting is not smooth, take your bike to a repair shop to adjust the derailleur. Doing this yourself can lead to more problems if you do not know what you’re doing. Again, chains are usually the first component to go in the drivetrain and should be replaced every 3,000-4,000 kms. Waiting too long to replace a chain will wear down the other drivetrain components faster.
Tune-up task #5: Check the tyres
What to do: Check your tyres for splits, cracks or tears, especially along the sides (where the tyre does not touch the ground). You will also want to check the tread for uneven or excessive wear. If the brake pads were out of alignment (task #2 above), make sure they have not damaged the tyres.
Tyres are fairly inexpensive to replace, so if you are in doubt about keeping a tyre, it is best to have it replaced. Damaged tyres are prone to burst, causing a sudden loss of control—a potentially dangerous situation. All bike shops will repair tyres, but it’s simple to change a tyre on your own using tyre levers and a pump to re-inflate the inner tube.
Tune-up task #6: Check the cables
What to do: Inspect the cable and surrounding rubber housing for cracks, crimps, rust, dirt and looseness.
New cables make shifting and braking smooth, which increases bike performance. If you notice damaged or worn out cables, get them replaced at your local bike shop. Unless you’re well trained in this task, changing bike cables can be tricky and time consuming. Schedule replacement of cables every 2-5 years based on use. If you ride your bike year-round, consider replacing your cables yearly.
Tune-up task #7: Add lubricant
What to do: Apply lubricant evenly to the chain while slowly rotating the pedals in a counterclockwise direction. Also, remember to lube moving parts on the derailleur, the pivot point on the brake levers and any exposed cable wire. Remember to wipe off any excess oil with a clean, dry rag, especially on the chain.
A properly lubricated bike makes shifting and braking smooth, thereby increasing performance. You can fix minor rust spots by rubbing them with steel wool. You may want to wear work gloves to protect your hands as steel wool can cause splinters in your skin. It is usually too difficult to remove rust from certain components (e.g., the chain), which should simply be replaced.